Tobee® B1036MS1-R55 Slurry Pump Frame plate liner is the main wear parts for the 1.5/1B-AH rubber lined slurry pump.
It forms a pump chamber with cover plate liner and throat bush to contact with slurries, As one of main wetted parts, Frame plate liner very easily worn-out components because it works under longtime impact of abrasive and corrosive slurries in the high speed conditions, So the materials is very crucial to lifetime of complete pump, Tobee provides a complete rubber materials selection for most all duties in mill.
Slurry Pump Rubber Frame Plate Liner Code:
|
Frame Plate Liner |
AH Slurry Pump |
Materials |
|
B1036 |
1.5/1B-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
B15036 |
2/1.5B-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
C2036 |
3/2C-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
D3036 |
4/3C-AH, 4/3D-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
E4036 |
6/4D-AH, 6/4E-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
F6036 |
8/6E-AH, 8/6F-AH, 8/6R-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
F8036 |
10/8F-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
G8036 |
10/8ST-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
FAM10036 |
12/10F-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
G10036 |
12/10ST-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
FAM12036 |
14/12F-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
G12043 |
14/12ST-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
H14043 |
16/14TU-AH |
Natural rubber, Synthetic rubber, Polyurethane |
|
U18043 |
20/18TU-AH |
Natural rubber, Synthetic rubber, Polyurethane |
1.5/1 BAH Slurry Pump Detailed Features:
• Horizontal,Cantilevered,Centrifugal,Single stage,Rubber lined slurry pump design.
• Casing - Casing halves of cast or ductile iron with external reinforcing ribs contain the wear liners and provide high operating pressure capabilities
• Bearing assembly - A large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame.
• Pump frame - A rigid, one-piece casting cradles the “cartridge” shaft and bearing assembly. A minimal number of through bolts hold the pump casing to the frame. An easy means of external impeller adjustment is provided in a convenient position below the bearing housing.
• Impeller - Front and rear shrouds have pump-out vanes. This design reduces recirculation and seal contamination, Elastomer impellers are made from rubber coated high tensile steel, Cast-in impeller threads require no impeller insert or nuts.
• Liners - Rubber elastomer liners are interchangeable with hard metal. The elastomer liners are bolted, not bonded, to the outer casing. Elastomer seal rings back all liner joints.
• Shaft seal - Packing seal,Centrifugal seal,Mechanical seal.
• Driving type - Flexible coupling,V-belt with pulleys,Gearbox,VFD,SCR control etc.
• The discharge branch can be oriented to any eight positions at the interval of 45 degrees;
• Easy to install and maintain in on-site application.
Added to subscribe successful !
